F-1 Felt
F1 White Felt
SAE F-1 specifications, uses, density and thicknessRecommended Uses:
SAE F-1 is suitable for oil retention in installations where the felt is not compressed, for feeding low viscosity or light oil, and where unusual strength and hardness are required. Washers, bushings, wicks, door bumpers, polishing blocks, and parts where wear and resistance to abrasion are required, are typical uses.
Minimum wool content: 95% wool.
Density:
Nominal (1”): 16.00 lbs/sq. yd.
Limits: 15.20 – 16.80 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-3 Felt
F3 Grey Felt
SAE F-3 specifications, uses, density and thicknessRecommended Uses:
SAE F-3 are recommended for vibration mountings and the same general purposes as SAE F-1 and where a felt of slightly lower quality is satisfactory.
Minimum wool content: 85% wool.
Density:
Nominal (1”): 15.60 lbs/sq. yd.
Limits: 14.41 – 16.79 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-5 Felt
F5 White Felt
SAE F-5 specifications, uses, density and thicknessRecommended Uses:
SAE F-5 is recommended for dust shields, wipers, grease retainer washers, wicks, vibration mountings, and in uses where a resilient felt is required.
Minimum wool content: 95% wool.
Density:
Nominal (1”): 12.24 lbs/sq. yd.
Limits: 11.60 – 12.88 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-7 Felt
F7 Grey Felt
SAE F-7 specifications, uses, density and thicknessRecommended Uses:
SAE F-7 is recommended for dust shields, wipers, grease retainer washers, wicks, vibration mountings, and in uses where a resilient felt is required.
Minimum wool content: 80% wool.
Density:
Nominal (1”): 12.24 lbs/sq. yd.
Limits: 11.60 – 12.88 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-10 Felt
F10 White Felt
SAE F-10 specifications, uses, density and thicknessRecommended Uses:
SAE F-10 is recommended for grease and oil retention where the felt is confined and compressed in assembly. Also recommended for dust shields under less severe operating conditions where F-5 & F-7 are not required.
Minimum wool content: 95% wool.
Density:
Nominal (1”): 8.48 lbs/sq. yd.
Limits: 7.84 – 9.12 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-11 Felt
F11 Grey Felt
SAE F-11 specifications, uses, density and thicknessRecommended Uses:
SAE F-11 is recommended for grease and oil retention where the felt is confined and compressed in assembly. Also recommended for dust shields under less severe operating conditions where F-5 & F-7 are not required.
Minimum wool content: 87% wool.
Density:
Nominal (1”): 8.48 lbs/sq. yd.
Limits: 7.84 – 9.12 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-13 Felt
F13 Grey Felt
SAE F-13 specifications, uses, density and thicknessMinimum wool content: 75% wool.
Density:
Nominal (1”): 8.48 lbs/sq. yd.
Limits: 7.84 – 9.12 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-15 Felt
F15 Grey Felt
SAE F-15 specifications, uses, density and thicknessMinimum wool content: 55% wool.
Density:
Nominal (1”): 8.48 lbs/sq. yd.
Limits: 7.84 – 9.12 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 3/16 Inch (4.76mm)
- 1/4 Inch (6.35mm)
- 5/16 Inch (7.94mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 5/8 Inch (15.88mm)
- 3/4 Inch (19.05mm)
- 7/8 Inch (22.23mm)
- 1 Inch (25.4mm)
F-26 Felt
F26 Grey Felt
SAE F-26 specifications, uses, density and thicknessRecommended Uses:
Soft padding and packing felt.
Minimum wool content: 45% wool.
Density:
Nominal (1”): 7.20 lbs/sq. yd.
Limits: 6.48 – 7.92 lbs/sq. yd.
Available Thicknesses:
- 1/8 Inch (3.18mm)
- 1/4 Inch (6.35mm)
- 3/8 Inch (9.53mm)
- 1/2 Inch (12.7mm)
- 3/4 Inch (19.05mm)
- 1 Inch (25.4mm)
F-50 Felt
F50 White Felt
SAE F-50 specifications, uses, density and thicknessRecommended Uses:
These are firm felts similar to F1 and F3 except the thickness is 3/32″ or less.
Minimum wool content: 95% wool.
Density:
Nominal (1”): 15.60 lbs/sq. yd.
Limits: 14.41 – 16.79 lbs/sq. yd.
Available Thicknesses:
- 1/16 Inch (1.59mm)
- 5/64 Inch (1.98mm)
- 3/32 Inch (2.38mm)
- 3/16 Inch (4.76mm)
F-51 Felt
F51 Grey Felt
SAE F-51 specifications, uses, density and thicknessRecommended Uses:
These are firm felts similar to F1 and F3 except the thickness is 3/32″ or less.
Minimum wool content: 92% wool.
Density:
Nominal (1”): 15.60 lbs/sq. yd.
Limits: 14.41 – 16.79 lbs/sq. yd.
Available Thicknesses:
- 3/64 Inch (1.19mm)
- 1/16 Inch (1.59mm)
- 5/64 Inch (1.98mm)
- 3/32 Inch (2.38mm)
F-55 Felt
F55 Grey Felt
SAE F-55 specifications, uses, density and thicknessRecommended Uses:
Similar to F7 but thickness is less than 1/8″. Used for sound deadening and anti squeak applications.
Minimum wool content: 75% wool.
Density:
Nominal (1”): 12.00 lbs/sq. yd.
Limits: 11.60 – 12.88 lbs/sq. yd.
Available Thicknesses:
- 1/16 Inch (1.59mm)
- 3/32 Inch (2.38mm)